Plastic machinery manufacturer
Ningbo, Chinasales@rhongplasticmachinery.com

Equipment selection guides

Compare equipment for production scrap, resin preparation and process cooling. Use the guides to define the material, operating conditions and installation.

Choose a processing route

How to compare plastic granulators for your scrap

Use the same material, output requirement and operating conditions when comparing machines. Start with the scrap that will actually reach the feed opening.

Read guide

Plastic granulator vs pelletizer: regrind or pellets?

A plastic granulator cuts solid scrap into regrind. A pelletizer cuts material after melt processing. Specify the required output and the equipment around each cutting stage before comparing quotations.

Read guide

Plastic scrap before granulation: keep material streams identifiable

Keep each scrap stream’s source and material records with it before collection makes those streams hard to distinguish. A granulator cuts material; it does not decide which streams can be mixed or reused.

Read guide

Beside-the-press or central granulation for injection molding?

Keep a suitable runner stream beside the press when its feeding rhythm, material identity and regrind destination fit the molding operation. Consider a central station for separately collected batches that need their own processing schedule. A factory can use both routes.

Read guide

Screenless vs screened granulators for injection molding sprues

A screenless granulator and a screened granulator can both recover injection molding sprues beside the press. Compare the cutting arrangement against the runner shape, the way it is fed and the regrind you need to reuse.

Read guide

Film scrap feeding: loose offcuts, edge trim and continuous web

The form of the incoming film determines the feeding discussion. Separate collected offcuts, continuous edge trim and a roller-fed web before comparing granulators.

Read guide

Plastic purgings: shredder, granulator or two stages?

The largest lump and the required regrind matter more than a machine label. Compare direct granulation with a shredding stage before choosing a route for solid purgings.

Read guide

Shredder vs Granulator for HDPE Drums: Can You Run Whole Drums?

Can you granulate HDPE drums whole? Compare three routes by feed interruptions and kilograms of usable regrind per hour, including preparation.

Read guide

Regrind percentage in injection molding: define and qualify the ratio

A regrind percentage is useful only when the permitted application and the mass used as its denominator are clear. Define both before setting a recipe or comparing equipment.

Read guide

Check specifications and quotations

Plastic Granulator Feed Opening vs Cutting Chamber: Will the Whole Part Fit?

A cutting chamber dimension is not a feed-opening dimension. To judge whether a whole scrap part suits a plastic granulator, follow its route to the inlet, through the feed path and into contact with the cutting system.

Read guide

Plastic Granulator Screen Size vs Regrind Size: Reading the Specification

Long, narrow flakes can pass end-first through a 6 mm round granulator screen hole even if they are longer than 6 mm. Ask for a trial with representative scrap. Record the size fractions and the test sieves used. Measure the longest dimension of long flakes separately, then check both results against your downstream acceptance criteria.

Read guide

Plastic granulator capacity: comparing kg/h ratings

Check what was processed, what was collected and how time was measured before comparing two plastic granulator capacity figures.

Read guide

Plastic granulator noise ratings: what does the number describe?

Two plastic granulators cannot be ranked by their dB(A) figures until you know what was measured. Identify the sound quantity, operating conditions and equipment included, then compare the results with the job and installation you are planning.

Read guide

Plastic granulator motor kW, supply requirements and energy use

A granulator’s motor kW rating does not tell you its whole-machine electricity demand or the energy a batch will use. Read the motor rating, electrical supply requirements and measured energy as three separate parts of the proposal.

Read guide

Plastic Regrind Bulk Density: kg/h, Litres and Hopper Volume

The same mass of regrind can occupy very different volumes. Use bulk density to compare a material flow in kg/h with the usable space in a hopper or collection container.

Read guide

Plastic Granulator Rotors and Knives: How to Compare Cutting Arrangements

Rotor body, knife arrangement and cutting geometry describe different parts of a granulator configuration. Learn how to compare them on the same material and operating basis.

Read guide

Cleaning, discharge and protection

Plastic Granulator Fines: What to Check Before Changing the Screen

More regrind fines do not point to one cause. Compare representative samples and check the cutting and collection conditions before specifying a smaller screen or dust separation.

Read guide

Plastic Granulator Cleaning Access for Colour and Material Changeover

Compare cleaning access across the actual material contact path, then record each stage of a colour or material changeover through quality release.

Read guide

Knife Maintenance and Spare Parts for a New Plastic Granulator

When buying a screened blade granulator, compare how its knives will be accessed, maintained and identified alongside the machine’s cutting configuration.

Read guide

Plastic Granulator Discharge: What to Include in Your Quotation

The granulator’s outlet is only one point in the material route. Define where regrind is collected, whether it must be transferred and what happens at the receiving point before comparing equipment quotations.

Read guide

How to Test Plastic Regrind Dust Removal Before Injection Molding

A cleaner stream can still cost you good regrind. Compare the feed, clean output and rejects from one batch, then record both results on a printable trial sheet.

Read guide

Protecting a Plastic Granulator from Metal Contamination: Magnets, Detection and System Response

Metal protection depends on where the device sits and what it does. Compare upstream and downstream goals, magnetic capture, detection and the response to a signal.

Read guide

Granulating Glass-Filled Plastic: Comparing Wear-Resistant Configurations

Glass-filled thermoplastic scrap can make wear resistance as important as nominal throughput. Compare the parts that actually contact the material, the scope of replaceable wear parts, and the conditions in which the machine will run.

Read guide

Drying, loading, mixing and cooling

Planning resin drying before molding or extrusion

Start with the material grade and its supplier's drying instructions. Then match the drying arrangement to material demand and the route to the processing machine.

Read guide

Gravimetric batch blender, volumetric doser or batch mixer for plastics?

Start with where each ingredient is measured and where the blend is prepared. Weight-based batch blending, volumetric process addition and separately measured batch mixing solve different preparation tasks; the existing mixer may still fit the workflow.

Read guide

Vacuum hopper loaders for plastic pellets: layout and receiver selection

Choose a pellet loader by reviewing the installation layout, receiving points, material route and operating demand together.

Read guide

Can Your Vacuum Loader Convey Plastic Regrind Flakes?

Keep the loader if the manufacturer confirms its exact configuration can handle your flakes. A trial on the intended route also needs to show that the blender has enough material at each draw and the regrind share by weight stays within the approved tolerance.

Read guide

Air-cooled vs water-cooled chillers for plastics: site conditions and supply scope

Air-cooled and water-cooled chillers differ on the condenser side. Compare the site requirements and complete supply scope before selecting a model.

Read guide

Industrial Chiller Cooling Capacity: Read kW, Tons and Rating Conditions

A chiller quotation may list cooling capacity and electrical input in kW alongside refrigeration tons. Read the units and rating conditions together before comparing offers.

Read guide

Can Your Chiller Handle Another Injection Molding Machine?

Adding an injection molding machine? Use measured flow and water temperatures to estimate spare cooling capacity. Check pressure and flow at the new branch separately.

Read guide

Water vs. Oil Mold Temperature Controllers for Injection Molding

Choose water when the controller and the entire mold circuit are rated for the fluid temperature and pressure the job requires. If the water proposal exceeds a mold, hose, fitting or seal limit, ask for an oil proposal and check its circuit separately. Give the supplier two temperatures: the target at the mold and the required fluid supply temperature.

Read guide

Resin dryer dew point vs resin moisture content: what to measure

A resin dryer dew point describes the sampled drying air. A resin moisture test describes a material sample. Both can inform acceptance, but they answer different questions.

Read guide

How to Size a Resin Drying Hopper for Your Production Rate

Start with actual hourly resin consumption and the grade-specific drying time, then check whether the hopper’s usable material volume and operating conditions support your production demand.

Read guide

Project checklists

Use these checklists to prepare project details and review the proposed equipment scope.

Need help selecting equipment?

Send your requirements or questions to RHONG.